- Location
- Fernhurst
- The job
- Compressor replacement, controls upgrade, system flush and ongoing servicing
- Equipment
- Panasonic 12kW air-to-water monobloc heat pump with a Viessmann 19kW back-up boiler
- Completed
- Compressor January 2024, with care continuing since
The challenge
A week before Christmas, this homeowner’s heating stopped. His Panasonic air-to-water heat pump, which works alongside a Viessmann back-up boiler, had failed, and the cause was the compressor: the heart of the heat pump.
We hadn’t installed the system, but he found us and asked us to sort it out. A compressor change is not a quick parts swap. It means working on the sealed refrigerant circuit, and it has to be done properly or the repair won’t last.
What we did
Compressor replacement (December 2023 to January 2024). As F-Gas certified engineers, we followed the full process:
- Diagnosed the failed compressor with full electrical and refrigerant checks.
- Isolated the system and recovered the existing refrigerant into a recovery cylinder.
- Removed the old compressor and filter drier, then brazed in the new ones while purging with oxygen-free nitrogen.
- Strength and pressure tested the circuit, then evacuated it to remove air and moisture.
- Recharged with 2.3 kg of virgin refrigerant, commissioned the system and leak-checked it.
- Updated the F-Gas records and site logbook, and disposed of the waste responsibly.
Smarter controls (May 2024). Next, we improved how the heat pump and boiler work together, so the boiler only helps when it’s really needed:
- Fitted a Viessmann cylinder demand box linked to the heat pump, so everything is still controlled through the heat pump as before.
- Added a pipe thermostat and a new Honeywell programmer. When the boiler is called in, it now runs in weather-compensated mode, adjusting its flow temperature to the weather outside.
- Kept the option for the heat pump to call for the boiler at full power on the coldest days.
- Fitted a new filling loop to cure a small leak, and showed the homeowner how the new controls work.
Flush and frost protection (November 2024).
- Replaced four automatic air vents in the loft.
- Flushed the system, added cleaner and flushed again.
- Refilled with Fernox HP-EG heat transfer fluid, protected to -12°C, then vented and tested everything.
The result
A heat pump that failed just before Christmas is still heating the home years later. The boiler now backs it up more efficiently, the system is protected against frost, and it’s in good working order.
He’s kept us on ever since for yearly servicing and checks, including a combined boiler and heat pump service where we fine-tuned the heat pump settings for hot water, vented the thermal store and set up the heating schedules and thermostats the way he wanted them.


Photos from the job



Have a heat pump that has stopped working, or one nobody will look after? We repair and service heat pumps, including systems we didn’t install. See our heat pump page, or get in touch for a quote.
More projects like this
Boilers and heatingFarnhamDIY thermal store to Viessmann boiler and solar, FarnhamA DIY thermal store with pumps, controllers and cables everywhere, replaced by a Viessmann system boiler, twin-coil cylinder and evacuated-tube solar.Read the story
Boilers and heatingFarnhamElectric boiler to Viessmann storage combiAn electric boiler swapped for a Viessmann 111-W storage combi and 440 accumulator, with a new concealed gas run and a hidden leaking cold main fixed.Read the story
Heat pumps and hot waterNorth Warnborough, near HookVented hot water to Mixergy, ready for solar, North WarnboroughAn old vented cylinder and noisy plastic pipework replaced with a Mixergy 180L smart cylinder, PV Switch and iBoost, ready for solar from day one.Read the storyReady when you are
Tell us what you need and we will come back to you with a clear, fixed price. No pressure, no hard sell.