Your home, just the right temperature Call 0800 246 1154 WhatsApp 07593 528328 hello@justtherighttemperature.co.uk

Why Is My Boiler Losing Pressure? Common Causes and Fixes

By Darren Marsh, Just The Right Temperature · 11 November 2026

If you find yourself topping up the boiler pressure every few weeks, or the boiler keeps locking out with a low pressure fault, you are not alone. It is one of the most common heating problems we see. Pressure does not disappear by itself: if it keeps dropping, water is escaping somewhere or a part is not doing its job. Here are the usual causes, what you can safely check, and when to call an engineer.

First, how a sealed system works

Most modern UK homes with a combi or system boiler have a sealed (pressurised) heating system. The water in the boiler, pipes and radiators is held under pressure, shown on a gauge or display on the boiler. There is no tank in the loft topping it up, so if water is lost, the pressure falls.

Many boilers are happy at around 1 to 1.5 bar when the heating is cold, but always check your boiler’s manual for the correct figure. It is normal for the pressure to rise a little when the system heats up and fall back as it cools. What is not normal is a steady drop over days or weeks.

The common causes of boiler pressure loss

1. A leak somewhere in the system

This is the most common cause. Even a slow drip can lose enough water over a few weeks to drop the pressure noticeably. Places to look:

Some leaks are hidden under floors or behind walls and are hard to find. If you cannot see one, that does not mean there is not one.

2. The expansion vessel has lost its charge

Water expands as it heats up. The expansion vessel is a tank, inside the boiler or mounted nearby, with a rubber diaphragm and a cushion of air or nitrogen on one side. It soaks up that expansion so the pressure does not spike.

Over time the vessel can lose its air charge. When that happens, the pressure climbs sharply as the system heats up, the pressure relief valve opens to protect the system, and water is lost. Then, when the system cools, the pressure drops below where it started. You top it up, and the cycle repeats.

A tell-tale sign is the gauge swinging a long way between cold and hot. Checking and recharging the vessel needs the right gauge and the system drained down to zero pressure on the boiler side, so it is a job for an engineer.

Engineer checking the pre-charge pressure of a heating expansion vessel with a digital gauge
Checking an expansion vessel's pre-charge with a digital gauge. This one matches the figure written on the vessel when it was set up.

3. A pressure relief valve that is letting by

The pressure relief valve (PRV) is a safety device that opens if the pressure gets too high. Its discharge pipe usually runs outside, often a small copper pipe poking out of the wall near the boiler. If that pipe drips, or you see staining below it, the valve is opening. Either the pressure is going too high (often the expansion vessel again) or the valve itself is worn and not sealing. Do not cap or block this pipe: it is there for safety.

4. Bleeding radiators

Bleeding radiators lets out trapped air, and that lowers the pressure. That is normal. If you bleed the radiators, check the pressure afterwards and top it up if needed. If you are bleeding the same radiators all the time, something is drawing air in or creating gas in the system, which is worth investigating.

5. Recent work on the system

If radiators have been removed for decorating, or the system has been drained, air can take a while to work its way out. The pressure may need topping up a few times. It should then settle. If it does not, there is likely another cause.

What you can safely check yourself

Never remove the boiler casing. Work inside the boiler on a gas appliance must be done by a Gas Safe registered engineer.

Why you should not just keep topping it up

Topping up once is fine. Topping up every week is treating the symptom. Each top-up brings in fresh water containing oxygen, which encourages corrosion and sludge, and dilutes the inhibitor that protects the system. A leak left alone can also damage floors and ceilings. Finding and fixing the cause is cheaper in the long run.

Digital gauge connected to a boiler's internal expansion vessel during a pressure check
Testing the internal expansion vessel inside a boiler. An undercharged vessel is a common reason for pressure that keeps dropping.

How we find the cause

When we look at a boiler that keeps losing pressure, we check the expansion vessel charge, the pressure relief valve and its discharge pipe, the filling loop, and the visible pipework and radiators. If the fault is a leak we cannot see, we will talk you through the options for tracing it. You get a clear explanation and a fixed price before we do any repair work.

An annual service is a good chance to catch these issues early, because the expansion vessel and pressure are part of the checks. You can book a service on our prices page, or see boiler servicing and heating repairs.

When it might be time for a new boiler

Most pressure problems are fixable. But if an older boiler has a failing internal vessel, worn components and a history of breakdowns, it can be worth comparing the cost of repairs with a replacement. We will give you an honest view either way. See our boiler installation page, and if you are thinking about hot water too, our hot water cylinders page. Real examples are in our case studies.

Questions we get asked

What should my boiler pressure be?

Many boilers sit around 1 to 1.5 bar when cold, but check the manual for your model. It will rise a little when the heating is on.

Is it dangerous if my boiler pressure is low?

Low pressure is not usually dangerous in itself, but the boiler may stop working to protect itself. Repeated loss means there is a fault to find.

Why does my boiler pressure go up when the heating is on?

Water expands as it warms, so a small rise is normal. A large rise often points to an expansion vessel that has lost its charge.

Can I recharge the expansion vessel myself?

We do not recommend it. On most boilers the vessel is inside the casing, and the system needs to be depressurised and the charge set correctly. It is a job for a Gas Safe registered engineer.

How quickly can you come out?

We aim to help as quickly as we can, and emergency callouts are same or next day when available. Call us on 0800 246 1154.

Ready when you are

Tell us what you need and we will come back to you with a clear, fixed price. No pressure, no hard sell.

Ready when you are

Tell us what you need and we will come back to you with a clear, fixed price. No pressure, no hard sell.

Where shall we send your free guide?

We'll only use your details to deal with your enquiry. We'll never share them. Privacy policy.